Portable DIY Mini Spot Welder Machine 18650 Battery Various Welding Power Supply

    Portable DIY Mini Spot Welder Machine 18650 Battery Various Welding Power Supply Specification & Description Summary

    Portable DIY Mini Spot Welder Machine 18650 Battery Various Welding Power Supply Specification

    • OriginCN(Origin)
    • Dimensions20cm
    • Max. Welding Thickness0.1mm to 0.12mm
    • UsageWelding

    100% brand new and high quality

    Features:

    1. Wide selection of welding power supply: lithium battery power supply or 12V car battery.

    2. The controller is controlled by a single chip microcomputer, and the output pulse is accurate to ensure the welding quality.

    3. With LCD display screen, can display welding parameters.

    4. The welding pen and the input line are connected by U-shaped cold-pressed terminals, which is convenient for disassembly and replacement.

    5. Using automatic touch welding mode, while retaining the manual trigger interface, you can choose according to your own use.

    6. The power board uses 2 Gusi copper to increase the overcurrent capacity.

    7, using 5 300A MOS tubes, non-disassembled MOS tubes.

    8. The MOS tube driver adopts the imported special chip driver. The fastest MOS tube can be hit with 20nS. The switch is fast to prevent the explosion of the tube and the non-triode push-pull drive.

    9. The MOS drive design adds a transient diode to protect the MOS and prevent the explosion of the tube.

    10. 10AWG multi-filament flexible wire is used for the welding pen line and the input line to increase the overcurrent capacity.

    11.The controller is mainly for welding nickel-plated steel strips from 0.1mm to 0.15mm.

    12. A 25V10000uF high-frequency low-resistance capacitor is added to the power input for energy compensation, which increases welding stability.

    Spot Welding Machine Set only,other accessories demo in the picture is not included.

     

    Instructions for use:

    1: Power connection

    The controller comes with a 20cm long 10AWG input wire. One end has been crimped with a U-shaped terminal, and the other end has not been processed. Connect the crimped U-shaped terminal to the control power input terminal, and the other end is processed according to its own power supply. Do not connect the negative electrode wrong.

    2: Switch on and off

    There is a power switch under the control board. After pressing, wait for 3 seconds. After the buzzer drops, the LCD lights up and the boot is complete. Press the power switch again to shut down.

    3: Screen description and parameter adjustment.

    4: Welding

    Keep the welding pin clean. If the welding pin is polished into a round head, the welding effect can be improved. There are manual and automatic methods.

     

    Specification:

    Material: Metal

    Input line length: app.20cm/7.87in

    Length of welding pen: app.30cm/11.81in

    Color: Red+Blue+Black

    Battery: 18650 lithium battery(not included)

     

    Note:

    No retail package.

    Please allow 0-1cm error due to manual measurement. pls make sure you do not mind before you bid.

    Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you!

     

    Package Contents:

    1Pc x Controller

    2Pcs x Welding pen

    2Pcs x Power input line (Red and Blue)

    1 Pair x U-shaped cold-pressed terminal (used to connect to input power)

    Several heat-shrinkable tubes, used to shrink the power input line

    1AA2014401AA201440-11AA201440-21AA201440-31AA201440-41AA201440-51AA201440-cmb

    100% brand new and high quality

    Features:

    1. Wide selection of welding power supply: lithium battery power supply or 12V car battery.

    2. The controller is controlled by a single chip microcomputer, and the output pulse is accurate to ensure the welding quality.

    3. With LCD display screen, can display welding parameters.

    4. The welding pen and the input line are connected by U-shaped cold-pressed terminals, which is convenient for disassembly and replacement.

    5. Using automatic touch welding mode, while retaining the manual trigger interface, you can choose according to your own use.

    6. The power board uses 2 Gusi copper to increase the overcurrent capacity.

    7, using 5 300A MOS tubes, non-disassembled MOS tubes.

    8. The MOS tube driver adopts the imported special chip driver. The fastest MOS tube can be hit with 20nS. The switch is fast to prevent the explosion of the tube and the non-triode push-pull drive.

    9. The MOS drive design adds a transient diode to protect the MOS and prevent the explosion of the tube.

    10. 10AWG multi-filament flexible wire is used for the welding pen line and the input line to increase the overcurrent capacity.

    11.The controller is mainly for welding nickel-plated steel strips from 0.1mm to 0.15mm.

    12. A 25V10000uF high-frequency low-resistance capacitor is added to the power input for energy compensation, which increases welding stability.

    Spot Welding Machine Set only,other accessories demo in the picture is not included.

     

    Instructions for use:

    1: Power connection

    The controller comes with a 20cm long 10AWG input wire. One end has been crimped with a U-shaped terminal, and the other end has not been processed. Connect the crimped U-shaped terminal to the control power input terminal, and the other end is processed according to its own power supply. Do not connect the negative electrode wrong.

    2: Switch on and off

    There is a power switch under the control board. After pressing, wait for 3 seconds. After the buzzer drops, the LCD lights up and the boot is complete. Press the power switch again to shut down.

    3: Screen description and parameter adjustment.

    4: Welding

    Keep the welding pin clean. If the welding pin is polished into a round head, the welding effect can be improved. There are manual and automatic methods.

     

    Specification:

    Material: Metal

    Input line length: app.20cm/7.87in

    Length of welding pen: app.30cm/11.81in

    Color: Red+Blue+Black

    Battery: 18650 lithium battery(not included)

    Quantity: 1Set

     

    Note:

    No retail package.

    Please allow 0-1cm error due to manual measurement. pls make sure you do not mind before you bid.

    Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you!

     

    Package Contents:

    1Pc x Controller

    2Pcs x Welding pen

    2Pcs x Power input line (Red and Blue)

    1 Pair x U-shaped cold-pressed terminal (used to connect to input power)

    Several heat-shrinkable tubes, used to shrink the power input line

    Product Details
    Portable DIY Mini Spot Welder Machine 18650 Battery Various Welding Power Supply

    Closeout Deals. Closeout Deals

    € 17,46
    4.7
    (based on 152 user reviews)
    Producer: MaJack
    Identifier: 4000985606806
    Volume Retail Sales: MaJack piece
    Availability: 414 pieces
    Last Update : Fri, 30 Oct 2020
  • follow us